55) DEFAULT NULL,
type VARCHAR(10) DEFAULT NULL,
content VARCHAR(65... AR(255) NOT NULL,
type VARCHAR(10) NOT NULL,
modified_at INT NOT NULL,
... ns
vi pdns.conf
query-local-address=192.168.178.100
# Back-end settings
load-modules=gpgsql
launch=... ameserver
recursor=192.168.178.1
allow-recursion=10.10.10.0/8,192.168.0.0/16
lazy-recursion=yes
</co
/dcf77-modul.html?search=dcf77|DCF77-Modul ]] für 10 € erhältlich.
Das Modul besteht aus einen kleine... 58 startet das HIGH Signal an SIG, dauert es nur 100ms wird das als eine logische 0 interpretiert, da... |
|21|1 min|
|22|2 min|
|23|4 min|
|24|8 min|
|25|10 min|
|26|20 min|
|27|40 min|
|28| Prüfbit für ger... Parität|
|29|1 h|
|30|2 h|
|31|4 h|
|32|8 h|
|33|10 h|
|34|20 h|
|35|Prüfbit für h gerade Parität |
|
erry|Raspberry mit Oracle Linux 9]]
===Windows 10===
Ab dem Raspberry Pi 2 (verwendet die Broadcom BCM2836 (ARMv7) CPU) kann auch Windows 10 installiert werden
Info:
* http://dev.windows.... tp://raspberry.tips/raspberrypi-tutorials/windows-10-iot-auf-dem-raspberry-pi-2-installieren/
----
==... 5°C
* accurate to ±0.5°C over the range of -10°C to +85°C.
* Programmable Resolution 1-Wire
out_port,RPIO.OUT)
#Frist Blink
for i in range(0,10):
#set the out port to HIGH
#LED ... _count)
time.sleep(2)
# end after 10 pushs
if (push_count > 10):
run=False
# Clean up
RPIO.cleanup()
</code>
=... e :: {}".format(gpio_id, val)
# end after 10 pushs
if (push_count > 10):
h [[http://www.elektronik-kompendium.de/sites/slt/1012151.htm|Dimensionierung einer Stabilisierungssch... eferenz valu
ref_voltage = 2.540
# runs
v_runs = 10
# Helper Function to set the bits
# set a bit t... IGH)
#Print the result
print "Value => {0:10.4f} :: binFormat :: {1} :: Bin Value :: {2}".form... runs = int(arg)
print "Referenz Voltage => {0:10.4f} :: Runs :: {1}".format(ref_voltage, v_runs)
von 50hz einfach mit einen Arduino oder einen LPC810 auszuwerten.
Dafür wird ein Widerstand in Reihe... atio : 30A/15mA
D.h. bei 1 A fließen 0,5mA, an 10 Ohm Burden Widerstand wären das dann eine Spannun... asheet => http://cds.linear.com/docs/en/datasheet/10178ff.pdf
Simulieren wir erst mal etwas mit LTS... tegrierte_Schaltkreise/analog/L/LT/LT1017CN8_i600_10246_0.htm, allerdings ist der nicht gerade günstig
wner/Peppy.doc/wiki/Express funktioniert fast zu 100%, nur ein paar kleine Anpassungen sind nötig.
... sfs=/devices/platform/soc/fe205000.i2c/i2c-22/i2c-10/10-0038/input/input5
U: Uniq=
H: Handlers=mouse0 event5
..
</code>
Wichtig ist der Name **"generic f... meter "/home/pi/myfifo"
meter_max 100
meter_show 0
spectrum "/home/pi/
utstärkeeinstellung und NF-Endverstärker
(Kosten ~10€)
Board mit dem Chip:
* http://www.ak-modul-bu... p://www.mikrocontroller.net/topic/342689
===AR1010===
Der AR1010 ist ein simpler über I2C oder SPI steuerbarer FM Empfänger (UKW).
* http://www.watterott.com/de/UKW-Empfaenger-AR1010
===RDA5807 ===
den RDA5807 gibt es recht günsti